Baujahr 2017 Cross strap, bundles/minute: 32/ opt. 36 At table belt speed in m/s: 1 Based on bundle size l x w in mm: 300 x 210 Depending on tension force Width in mm: 150 - 420 Length in mm: 150 - 420 Height in mm: 10 - 400 Weight in kg: max. 25 TRANSPORT SPEED m/s: 0,20 - 1,00 Steplessly adjustable Automatic strap tensioning, stepless, depending on height of bundle Tension at bundle in N: max. 325 Tension path in mm: max. 200 STRAPPING MATERIAL Polypropylene DIN EN 13 394 Width in mm: 5 - 9 Thickness in mm: 0.4 - 0.55 Heat seal. Tensile strength of welded joint is approx. 80% of the breaking strength of the strap Core ID in mm: 200 Core OD in mm: 420 Width in mm: 190 (160,180,200) Wide Range Input 380-520V, 3AC; 47 63 Hz Maximum fusing 16A (B-character) Protection Type: IP 54 Power consumption in kW approx.: 0,75 Total weight approx. in kg: 830
- Ref.-Nr:
- 27370
- Manufacturer:
- SMB
Baujahr 1999 Max. Paper Size 52.00 x 0.00 cm flat pile feeder with suction head counter MCS 106 4 folding pockets in the parallel fold section segmented folding rollers following knife shaft 2 folding knives in the cross fold section 1 additional folding pocket after the 1st cross fold stream delivery
- Ref.-Nr:
- 27297
- Manufacturer:
- GUK
Direction: left - right Range: max. 150 mm hight label Capacity: Upperbelt max 310 mm Hight Dimensions: L x W x H = 4.050 x 1.350 x 1.550 mm Weight: 250 Kg Frame: Stainless steel/ aluminium Electric: 380 Volt – 50 Hz – 1,2 kW Features: Conveyor 4.050 mm long (can be Shortened ) 89 mm wide slat belt chain roll on belt is 150mm high
- Ref.-Nr:
- 27292
- Manufacturer:
- Herma
MBO mobile corner conveyor table ET 46 with ball rail ET 46 can be swiveled through 180° suitable for both left and right installation. The ET 46 alignment ruler is equipped with a ball bar for standard products. Format: 46 cm
- Ref.-Nr:
- 27276
- Manufacturer:
- MBO
rotary feeders with adjustable interface, 970 mm high
- Ref.-Nr:
- 27251
- Manufacturer:
- Buhrs
rotary feeders with adjustable interface, 970 mm high
- Ref.-Nr:
- 27250
- Manufacturer:
- Buhrs
Built in/YOC: 2006 Technical Data: Size: min 114 x 162 mm, max 250 x 353 mm Size product: min 105 x 148 mm, max 229 x 324 mm Product thickness rotary feeder: max 3 mm Product thickness shuttle feeder: max 10 mm Product thickness Vacuum/Friction feeder: max 13 mm Paper weight: min 80 g/m2, max 180 g/m2 Speed: max 10.000 c/h Equipment: · 8 Base stations · 6 Rotary feeder · 1 Shuttle feeder · 1 Inserting station · 1 Envelope feeder · 1 Outfeed left · 1 Reject device · 1 Turning belt · 1 Stream delivery · 1 Simatic touch panel Optional equipment (not included!): · 1 Balsfulland Base controller · 2 Balsfulland BVS 8000 · 1 Balsfulland BVS 8000 Product Shift Box All technical data is for information purposes only! Although the technical information is mostly taken from manufacturers documents, no guarantee can be given for correctness due to e.g. undocumented changes of the equipment. By no means are these values intended to be binding or part of the contract.
- Ref.-Nr:
- 27233
- Manufacturer:
- Buhrs
Machine number: Y201095 Built in: 2017 Size: DL-C4 mm Speed: 10.000 c/h Equipment • 6 station base • 5 rotary feeder • 1 inserting station • 1 reject gate • 1 envelope feeder • 1 belt delivery optional equipment: -- not included -- • extra rotary feeders • shuttle feeders • delivery system Condition: good working, machine can be inspected in production
- Ref.-Nr:
- 27231
- Manufacturer:
- W+D
Type of strapping: single & double max speed for single strap: 36 bundles/min max speed for parallel (double) strap: 19 bundles/min min bundle dimensions (w x l): ~200 x 170 mm max bundle dimensions (w x l): ~560 x 560 mm min bundle (package) height: ~10 mm max bundle (package) height: ~440 mm max weight bundle/package: 25 kg Infeed / outfeed (conveying) height: ~800-930 mm Continuously adjustable conveyor speed Metric input of strapping position Type of sealing: heat-weld sealing Strapping material: Polypropylen (PP) No of strap coil dispenser: single Strap coil dispenser - core diameter: 200 mm Strap coil dispenser - core width: 190 mm Equipped with back stop (package stop) Equipped with hold-down device Equipped with interface to up-/downstream equipment Weight: ~550 kg
- Ref.-Nr:
- 27223
- Manufacturer:
- Ampag
- Type of strapping: single & double - max speed for single strap: 36 bundles/min - max speed for parallel (double) strap: 19 bundles/min - min bundle dimensions (w x l): ~200 x 170 mm - max bundle dimensions (w x l): ~560 x 560 mm - min bundle (package) height: ~10 mm - max bundle (package) height: ~440 mm - max weight bundle/package: 25 kg - Infeed / outfeed (conveying) height: ~800-930 mm - Continuously adjustable conveyor speed - Metric input of strapping position - Type of sealing: heat-weld sealing - Strapping material: Polypropylen (PP) - No of strap coil dispenser: single - Strap coil dispenser - core diameter: 200 mm - Strap coil dispenser - core width: 190 mm - Equipped with back stop (package stop) - Equipped with hold-down device - Equipped with interface to up-/downstream equipment - Over all length equipment: ~736 mm - Over all width equipment: ~1360 mm - Over all height equipment: ~1915 mm - Input Power: 1,5 kVA - Voltage: 400V, 50/60 Hz, 3Ph, N - Air requirement: 330l/min freie Luft @ 6 bar - Weight: ~550 kg
- Ref.-Nr:
- 27222
- Manufacturer:
- Ampag
High speed up to 65 straps per minute Free access to strap guides (patents registered) Waist-high auto strap feeding Waist-high quick coil change (patents registered) Turnable operating control panel Auto strap ejector Dispenser release switch Sensor controlled heater Low voltage Strap end ejector Front foot bar switch Adjustable table height between 820 mm and 920 mm Photo-eye switch Rear foot bar switch Foot pedal switch Lower adjustable table height (770 mm - 820 mm) Capacity: Up to 65 cycles/minute (TP-702-59) Up to 60 cycles/minute (TP-702-12) Strap Width: 5 mm, 6 mm, or 9 mm (TP-702-59) 12 mm (TP-702-12) Tension Range: 1 to 32 kg (TP-702-59) 1 to 45 kg (TP-702-12) * Higher tension is on request Weight: 158 kg (TP-702-59) 167 kg (TP-702-12) Electrical Requirements: 110V, 220V, 230V, 240V 50/60Hz 1PH
- Ref.-Nr:
- 27212
- Manufacturer:
- Ampag
Size: max 320 x 384 mm Size trimmed: max 304 x 310 mm, min 70 x 136 mm Speed: max 4.000 c/h, min 1.000 mm Power requirements: 7 kW (220/380V, 50Hz) Air requirement (6 bar): 40 m³/h Width: 3.612 mm Depth: 1.970 mm Height: 2.020 mm Weight: 3.500 kg (approx.) Equipment: • belt feeding • automatic infeed with integrated pre stacker • make-ready system • silicone spraying device • external knife changing device • equipment for changing the format: • 1 set of pressing plates & holders • 1 set of table quick change plates • 3 sets of cutting sticks • 2 set of knives • central lubrication • belt delivery • 1 set of operator manuals • 1 set of electrical diagrams • 1 set of standard tools • 1 spare part catalogue • standard equipment
- Ref.-Nr:
- 27177
- Manufacturer:
- Müller Martini
Built in: 2003 Size max: 480 x 320 mm Sizes untrimmed high folio lap: max 480 x 320 mm min 105 x 115 mm with Accessories: 90 x 80 mm Sizes untrimmed low folio lap: max 480 x 300 mm min 105 x 125 mm Mechanical Speed: 21" chain pitch 12.000 c/h Power consumption: max 11,0 kW Compressed air (to be supplied by purchaser): depending on configuration 6 bar working hours: 21466 thsd.h Equipment gathering chain & feeder • 6 station gathering track & chain • 4 flat pile feeders 370 • 1 cover folder feeder 1529 stitching unit • stitching unit 380 • transfer left • wire unwind device • thickness control/ plus-minus • 2 stitching heads HK 75 three knife trimmer • three knife trimmer 449 knives • 2 sets of knives standards • 1 set of operator manuals • 1set of electrical diagrams • 1 spare part catalogue • 1 set of tools • further information • location: D-Helmstedt • machine can be tested under power • cleaned & checked available • immediately • additional feeders • double production device • small book attachment • compensating stacker • card gluer • Inline inserting machine with 2 up to 10 stations
- Ref.-Nr:
- 27173
- Manufacturer:
- Müller Martini
Built in 1996 Size max 480 x 320 mm Size untrimmed max 480 x 320 mm min 153 x 108 mm Size trimmed max 475 x 300 mm min 148 x 105 mm Product thickness max 13 mm Speed max 13.000 c/h Equipment gathering chain & feeder • 6 station gathering track & chain • 5 feeders 370 • 1 cover folder feeder stitching unit • stitching unit 390 • wire unwind device • thickness control/ plus-minus • 2 stitching heads three knife trimmer • three knife trimmer 360 knives • 2 sets of knives
- Ref.-Nr:
- 27172
- Manufacturer:
- Müller Martini
Machine number: 91.05666 Built in: 1997 Size: max 480 x 320 mm Size untrimmed: max 480 x 320 mm, min 153 x 108 mm Size trimmed: max 475 x 300 mm, min 148 x 105 mm Product thickness: max 13 mm Speed: max 13.000 c/h Number of heads: max 6 Equipment gathering chain & feeder • 5 station gathering track & chain • 4 feeders 370 • 1 cover folder feeder 1529 stitching unit • stitching unit 390 • wire unwind device • thickness control/ plus-minus • 2 stitching heads three knife trimmer • three knife trimmer 360 knives • 2 sets of knives • Doppelnutzeneinrichtung • Betriebsstunden: 34.088h
- Ref.-Nr:
- 27163
- Manufacturer:
- Müller Martini
Built in 2003 Size: max 510 x 320 x 60 mm min 200 x 72 x 3 mm Equipment • turnover belt
- Ref.-Nr:
- 27134
- Manufacturer:
- Müller Martini
Size: max 480 x 325 mm Size untrimmed with lap: max 480 x 325 mm, min 90 x 115 mm Size untrimmed without lap: max 440 x 300 mm, min 158 x 115 mm Size trimmed with lap: max 470 x 320 mm, min 148 x 105 mm Size trimmed without lap: max 430 x 295 mm, min 148 x 105 mm Speed max: 14.000 c/h Power requirements: 11-18 kW (220/380V, 50Hz) Equipment gathering chain & feeder • 7 station gathering track & chain • 4 double base • 6 feeders 345 • 1 cover folder feeder 1529 stitching unit • stitching unit 300 • wire unwind device • thickness control/ plus-minus • 2 stitching heads HK 75 three knife trimmer • three knife trimmer 251 knives • 2 sets of knives delivery • belt delivery standard accessories • 1 set of operator manuals • 1set of electrical diagrams • 1 spare part catalogue • 1 set of tools further information • location: D- Braunschweig • next airport: Germany-Hannover • condition: very good
- Ref.-Nr:
- 27126
- Manufacturer:
- Müller Martini
Year: 2016 Description Product Length: Minimum: 180 mm (7.09") Maximum: 500 mm (19.70") Product Width: Minimum: 145 mm (5.71") Maximum: 320 mm (12.60") Compressed Log Length: Minimum: 700 mm (27.56") Maximum: 1,200 mm (47.24") Maximum Log Weight: 170 kg (375 lbs) Cycle Time: 17 seconds (product dependent) Palletizing Height: Bottom edge of log: 100 mm (3.93") Top edge of log: 1,500 mm (59.06") Pick-Up Height: 900 mm (35.43") Electrical Supply: 400 V 3 Phase (3~) N + PE 50/60 Hz Installed Power: 1.6 kW Compressed Air Requirement: 65 l/min at 6 bar (87 psi) Maximum of 4 cycles per minute Hose connection: Ø 13 mm Machine Weight: 1,300 kg (2,870 lbs)
- Ref.-Nr:
- 27125
- Manufacturer:
- Rima
Built in: 1990 Cutting width max: 1.550 mm Feeding height max: 130 mm Feeding depth max: 1.150 mm Front table length: 620 mm Table height: 900 mm Power requirements: 3 kW (220/380V, 50Hz) Clamping pressure min: 300 daN Clamping pressure: 3.700 daN Width: 1.960 mm Depth: 2.260 mm Height: 1.480 mm Weight: 2.750 kg (approx.) Equipment •: air table Accessories: • 1 set of operator manuals • 1 set of electrical diagrams • 1 set of standard tools • 1 spare part catalogue • standard equipment
- Ref.-Nr:
- 27123
- Manufacturer:
- Schneider Senator
Built in: 2001-2003 Size: max 290 x 420 x 65 mm; min 100 x 105 x 3 mm Speed: max 15.000 c/h Equipment gathering machine • chain tensioner • 12 stations • gatherer ZU 840 • 8 streamfeeder STA 840 • reject unit AS 840 controls • opticontrol signature image reader intermediate elements • reject unit • jogging element perfect binder • Copilot • Monitor control • 23 clamps • jogging station • resting table • fold pressing station • milling and roughening station • equalizing-leveling station • hotmelt spine gluing unit • hotmelt side gluing unit • 2 premelters • stream cover feeder • cover pressing station • smooth lay down device conveyor system • bypass for splitting saw splitting saw • turnover belt • connected with three knife trimmer • destacker • information three knife trimmer: HD 151 P compensating stacker • information compensating stacker: Müller Martini CB 16 standard accessories • pv pressure-vacuum pump • 1 set of electrical diagrams • 1 set of spare part catalogues • 1 set of tools further information • machine can be tested in production • condition: working condition
- Ref.-Nr:
- 27091
- Manufacturer:
- Kolbus
Height: max 1.800 mm Pallet format: max 1.000 x 1.200 mm Speed: max 30 pallets/h Electrics: 380 VAC Electrics: 50 Hz Electrics: 3 PH holding power: max 5.500 N Equipment • strapping machine: XP-112 MV • sealing head CFH-1 • stretch wrapper: GL-215 • control: S7
- Ref.-Nr:
- 27063
- Manufacturer:
- Cyklop
Cutting width max: 1.150 mm Feeding height max: 165 mm Feeding depth max: 1.150 mm Front table length: 715 mm Table height: 860 mm Power requirements: 4 kW (220/380V, 50Hz) Width: 2.280 mm Depth: 2.600 mm Height: 1.600 mm Weight: 3.500 kg (approx.) Equipment: standards • 1 set of operator manuals • 1 set of electrical diagrams • 1 spare part catalogue • standard equipment • 1 set of standard tools
- Ref.-Nr:
- 27060
- Manufacturer:
- Polar
Size max: 500 x 330 mm Size min: 140 x 105 mm Size (diagonal) max: 560 mm Number of pages max: 128 St. Number of pages min: 4 St. Pile height max.: 400 mm section height max: 250 mm Infeed height: 560 – 970 mm Delivery height: 887 mm Cycle per layer: ≥ 1,7 s Air consumption: 1.200 Nl/min (@ 1 bar) Voltage: 400, 3~, N, PE V Sicherung: 16 A Frequency: 50 Hz Length: 3.218 mm Width: 955 mm Height: 2.075 mm Weight: ca. 1.400 kg
- Ref.-Nr:
- 27059
- Manufacturer:
- Gämmerler

